产品
Location : tinplate sheet and coil prime electrolytic tinplate sheet and coil MR EN10202 standard

tinplate sheet and coil

prime electrolytic tinplate sheet and coil MR EN10202 standard

Source:   Updated:2015-12-15   Hits:

DOWNLOAD

  Product Description
Standard for temper
Chinese Standard Japanese Standard American Standard  European Standard
GB/T 2520-2008 JIS G3303-2008 ASTM A623M-06a DIN EN10202-2001
T-1  T-1 T-1 (T49) TS230
T1.5
T-2 T-2 T-2 (T53) TS245
T-2.5 T-2.5   TS260
T-3 T-3 T-3 (T57) TS275
T-3.5 TS290
T-4 T-4 T-4 (T61) TH415
T-5 T-5 T-1 (T65) TH435
DR-7M DR-7.5 TH520
DR-8 DR-8 DR-8 TH550
DR-8M DR-8.5 TH580
DR-9 DR-9 DR-9 TH620
Electrolytic Tinplate sheet coil specifications
Steel Type       SPCC, MR
Temper(BA&CA)      T1~T5
Coating      1.1~11.2g/m2
Thickness and tolerance      0.15~0.50mm(Tolerance: _+0.01 mm)
Width & tolerance       300~1000mm (Tolerance: 0~3mm)
Cut length & tolerance         450~``50mm (Tolerance: 0~3mm )
Coil inside diameter       420/508mm
Coil Weight         3~10 MT
Passivation         311
Oiling               DOS
Surface Finish       Bright, Stone, Silver, Matte
Packaging             Seaworthy Standard with wooden pallet
Standards Available       GB/T2520, JIS G3303, ASTM A623M & EN10202
Special specitications are available on request.
Tin coating weight
Type Designation of tin       coating weight Min.average tin coating weight(g/m2) Former Coating Designation
Equal tin coating 1.4/1.4 1.2/1.2 #15
2.2/2.2 2.0/2.0 #20
2.8/2.8 2.45/2.45 #25
5.6/5.6 5.05/5.05 #50
8.4/8.4 7.55/7.55 #75
11.2/11.2 10.1/10.1 #100
Differentially Coating 1.4/2.8 1.2/2.45 #15/25
2.2/2.8 2.2/2.45 #20/25
2.8/5.6 2.45/5.05 #25/50
2.8/8.4 2.45/7.55 #25/75
2.8/11.2 2.45/10.1 #25/100
5.6/8.4 5.05/7.55 #50/75
5.6/11.2 5.05/10.1 #50/100
8.4/11.2 7.55/10.1 #75/100
Surface finish
Surface finish Nominal surface roughness (um Ra) Characteristic
Bright finish Q0.35 Glazed surface obtained after melting treatment of electrotinned smooth raw materail strip with extremely fine rubstone fingure by processing.
Stone finish 0.25~0.60 Glazed surface obtained after melting treatment of electrotinned smooth raw materail stripfeaturing certain rubstone figures.
Silver finish 0.50~1.00 Glazed surface obtained after melting treatment of electrotinned smooth raw material strip with rough matt furface.
Matte finish 0.80~2.50 Matt surface of general matt raw material strip without melting treatment.

 

Please fill in the table below your message, we will reply you within 24 hours! (with the *is required) Name : Tel: Zip code : E-mail : * Address : Title : content : * Captcha: *